Application module: Sequential laminate assembly design ISO/TS 10303-1741:2018-11(E)
© ISO

Cover page
Table of contents
Copyright
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
    3.1 Terms and definitions
    3.2 Abbreviated terms

4 Information requirements
   4.1 Required AM ARM
   4.2 ARM type definitions
   4.3 ARM entity definitions
5 Module interpreted model
   5.1 Mapping specification
   5.2 MIM EXPRESS short listing
     5.2.1 MIM type definitions
     5.2.2 MIM entity definitions

A MIM short names
B Information object registration
C ARM EXPRESS-G   EXPRESS-G
D MIM EXPRESS-G   EXPRESS-G
E Computer interpretable listings
F Change history
Bibliography
Index

5.2 MIM EXPRESS short listing

This clause specifies the EXPRESS schema derived from the mapping table. It uses elements from the common resources or from other application modules and defines the EXPRESS constructs that are specific to this part of ISO 10303.

This clause constitutes the Module Interpreted Module (MIM) of the application module.

This clause also specifies the modifications that apply to the constructs imported from the common resources.

The following restrictions apply to the use, in this schema, of constructs defined in common resources or in application modules:

Short names of entities defined in this schema are described in Annex A. Unambiguous identification of this schema is defined in Annex B.

EXPRESS specification:

*)
SCHEMA Sequential_laminate_assembly_design_mim;

USE FROM Layered_interconnect_module_design_mim;    --  ISO/TS 10303-1698
(*

NOTE 1   The schemas referenced above are specified in the following part of ISO 10303:

Layered_interconnect_module_design_mim ISO/TS 10303-1698

NOTE 2   See Annex D, Figures D.1and D.2 for a graphical representation of this schema.

5.2.1 MIM type definitions

This subclause specifies the MIM types for this application module. The MIM types and definitions are specified below.

5.2.1.1 slad_groupable_item   EXPRESS-G

The slad_groupable_item type is an extension of the groupable_item type. It adds the data types group_relationship, and assembly_component_usage to the list of alternate data types.

EXPRESS specification:

*)
TYPE slad_groupable_item = SELECT BASED_ON groupable_item WITH
   (group_relationship,
    assembly_component_usage);
END_TYPE;
(*

5.2.1.2 slad_requirement_assigned_item   EXPRESS-G

The slad_requirement_assigned_item type is an extension of the requirement_assigned_item type. It adds the data types derived_laminate_assignment, and assembly_component_usage to the list of alternate data types.

NOTE  The list of entity data types may be extended in application modules that use the constructs of this module.

EXPRESS specification:

*)
TYPE slad_requirement_assigned_item = EXTENSIBLE GENERIC_ENTITY SELECT BASED_ON requirement_assigned_item WITH
   (derived_laminate_assignment,
    assembly_component_usage);
END_TYPE;
(*

5.2.2 MIM entity definitions

This subclause specifies the MIM entities for this module. The MIM entities and definitions are specified below.

5.2.2.1 derived_laminate_assignment   EXPRESS-G

A derived_laminate_assignment is a type of property_definition_relationship that implements the ARM concept of Derived_laminate_assignment.

EXPRESS specification:

*)
ENTITY derived_laminate_assignment
  SUBTYPE OF (property_definition_relationship);
END_ENTITY;
(*

5.2.2.2 interconnect_module_stratum_based_terminal   EXPRESS-G

An interconnect_module_stratum_based_terminal is a type of interconnect_module_terminal that implements the ARM concept of Interconnect_module_stratum_based_terminal.

EXPRESS specification:

*)
ENTITY interconnect_module_stratum_based_terminal
  SUBTYPE OF (interconnect_module_terminal);
END_ENTITY;
(*

5.2.2.3 sequential_laminate_passage_based_fabrication_joint   EXPRESS-G

A sequential_laminate_passage_based_fabrication_joint is a type of shape_aspect that implements the ARM concept of Interconnect_module_product_assembly_view_fabrication_joint.

EXPRESS specification:

*)
ENTITY sequential_laminate_passage_based_fabrication_joint
  SUBTYPE OF (shape_aspect);
END_ENTITY;
(*

5.2.2.4 sequential_laminate_stackup_component   EXPRESS-G

A sequential_laminate_stackup_component is a type of physical_component that implements the ARM concept of Sequential_laminate_stackup_component.

EXPRESS specification:

*)
ENTITY sequential_laminate_stackup_component
  SUBTYPE OF (physical_component);
END_ENTITY;
(*

5.2.2.5 sequential_laminate_stackup_definition   EXPRESS-G

A sequential_laminate_stackup_definition is a type of product_definition that implements the ARM concept of Sequential_laminate_stackup_definition.

EXPRESS specification:

*)
ENTITY sequential_laminate_stackup_definition
  SUBTYPE OF (product_definition);
END_ENTITY;
(*



*)
END_SCHEMA;  -- Sequential_laminate_assembly_design_mim
(*


© ISO 2018 — All rights reserved