ISO/TS 10303-1206:2014-02 Draughting annotation


Application module: Draughting annotation	ISO/TS 10303-1206:2014-02(E) © ISO

Cover page
Table of contents
Copyright
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
3.2 Abbreviated terms

4 Information requirements
4.1 Required AM ARM
4.2 ARM type definitions
4.3 ARM entity definitions
4.4 ARM subtype constraint definition
5 Module interpreted model
5.1 Mapping specification
5.2 MIM EXPRESS short listing
5.2.1 MIM entity definitions

A MIM short names
B Information object registration
C ARM EXPRESS-G
D MIM EXPRESS-G
E Computer interpretable listings
F Change history
Bibliography
Index

Contents

1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
3.2 Abbreviated terms
4 Information requirements
4.1 Required AM ARM
4.2 ARM type definitions
          4.2.1 da_draughting_callout_content_select
          4.2.2 symbol_definition_select
4.3 ARM entity definitions
          4.3.1 Annotation_subfigure
          4.3.2 Annotation_symbol
          4.3.3 Dimension_curve_terminator
          4.3.4 Dimension_symbol
          4.3.5 General_symbol
          4.3.6 Geometric_tolerance_symbol
          4.3.7 Surface_condition_symbol
          4.3.8 Terminator_symbol
4.4 ARM subtype constraint definition
          4.4.1 alternate_annotation_elements
5 Module interpreted model
5.1 Mapping specification
          5.1.1 Annotation_subfigure
          5.1.2 Annotation_symbol
          5.1.3 Dimension_curve_terminator
          5.1.4 Dimension_symbol
          5.1.5 Draughting_callout
          5.1.6 General_symbol
          5.1.7 Geometric_tolerance_symbol
          5.1.8 Surface_condition_symbol
          5.1.9 Terminator_symbol
          5.1.10 alternate_annotation_elements
5.2 MIM EXPRESS short listing
5.2.1 MIM entity definitions
          5.2.1.1 pre_defined_dimension_symbol
          5.2.1.2 pre_defined_geometrical_tolerance_symbol
          5.2.1.3 pre_defined_surface_condition_symbol
Annex A MIM short names
Annex B Information object registration
   B.1 Document identification
   B.2 Schema identification
Annex C ARM EXPRESS-G
Annex D MIM EXPRESS-G
Annex E Computer interpretable listings
Annex F Change history
F.1 General
F 2 Changes made in edition 2
F 2.1 Summary of changes
F 2.2 Changes made to the ARM
F 3 Changes made in edition 3
F 3.1 Summary of changes
F 3.2 Changes made to the ARM
Bibliography
Index

Figures

Figure 1 — Annotation subfigure for a hole on a technical drawing
Figure 2 — Predefined dimension symbols
Figure 3 — Predefined geometrical tolerlance symbols
Figure 4 — Pre-defined surface condition symbols
Figure 5 — Predefined terminator symbols
Figure C.1 — ARM schema level EXPRESS-G diagram 1 of 1
Figure C.2 — ARM entity level EXPRESS-G diagram 1 of 1
Figure D.1 — MIM schema level EXPRESS-G diagram 1 of 1
Figure D.2 — MIM entity level EXPRESS-G diagram 1 of 1

Tables

Table A.1 — MIM short names of entities
Table E.1 — ARM and MIM EXPRESS listings

© ISO 2014 — All rights reserved